Mesa, AZ Heating and Air Conditioning Services

Morehart Air Conditioning & Heating provides heater and air conditioning repair,  installation and services in Mesa, AZ and surrounding areas.

Check out what some of our customers are saying about Morehart Air Conditioning & Heating  services.

Local Reviews
for Mesa, AZ


Tom G.

Tom G.

In Mesa, near East Fairfield Street and North Amber Circle replacing a 825 rpm fan motor with 7.5 uf capacitor. This York system is in really bad condition and needs replacement. Will need to see if compressor holds with repair.

Near E Fairfield St, Mesa, AZ 85203
Mesa, AZ - In Mesa, near East Fairfield Street and North Amber Circle replacing a 825 rpm fan motor with 7.5 uf capacitor. This York system is in really bad condition and needs replacement. Will need to see if compressor holds with repair.
Tom G.

Tom G.

In Mesa, near Signal Butte Floodway and North Vincent Circle performing a diagnostic on a Trane condenser. Fan motor was seized and capacitor swollen upon arrival. Replaced capacitor and motor. Charged system with 3 lbs of R22. Unit is working properly upon departure.

Near N Vincent Cir, Mesa, AZ 85207
Mesa, AZ - In Mesa, near Signal Butte Floodway and North Vincent Circle performing a diagnostic on a Trane condenser. Fan motor was seized and capacitor swollen upon arrival. Replaced capacitor and motor. Charged system with 3 lbs of R22. Unit is working properly upon departure.
Brian S.

Brian S.

In Mesa, AZ: DIAGNOSTIC- On arrival, found compressor not running. Checked run capacitor and found 1.1/5.8/440; should be at 40/5/440. Talked to customer about replacing capacitor and adding a hard start kit. Customer approved the 40/5/440 capacitor and declined the hard start kit. Installed new capacitor and cycled system on. Upon departure, system is running properly and within manufacturer specifications. Service complete. Return 91/Supply 71.

Near E Monte Ave, Mesa, AZ 85209
Mesa, AZ - In Mesa, AZ:  DIAGNOSTIC-  On arrival, found compressor not running. Checked run capacitor and found 1.1/5.8/440; should be at 40/5/440. Talked to customer about replacing capacitor and adding a hard start kit. Customer approved the 40/5/440 capacitor and declined the hard start kit. Installed new capacitor and cycled system on. Upon departure, system is running properly and within manufacturer specifications. Service complete. Return 91/Supply 71.
Leonardo G.

Leonardo G.

In Mesa, AZ: DIAGNOSTIC- Upon arrival, cycled unit into cooling mode. Found system low on charge about a pound or two. Recharged system to correct specification. Upon departure, unit is working properly and within manufacturer specifications.

Near E Kiva Ave, Mesa, AZ 85209
Mesa, AZ - In Mesa, AZ:  DIAGNOSTIC-  Upon arrival, cycled unit into cooling mode. Found system low on charge about a pound or two. Recharged system to correct specification. Upon departure, unit is working properly and within manufacturer specifications.
Brian S.

Brian S.

In Mesa, AZ: DIAGNOSTIC- Customer stated that George Brazil installed a new run capacitor on his system last week and told him he should change out system. Checked Freon levels; all in factory specification. Checked volt and amp draws. Compressor Rated 16.0/Actual 14.37. Outdoor fan motor Rated 2.0/Actual 1.05. System is 20 years old but running properly at this time. Service complete.

Near N 74th St, Mesa, AZ 85207
Mesa, AZ - In Mesa, AZ:  DIAGNOSTIC-  Customer stated that George Brazil installed a new run capacitor on his system last week and told him he should change out system. Checked Freon levels; all in factory specification. Checked volt and amp draws. Compressor Rated 16.0/Actual 14.37. Outdoor fan motor Rated 2.0/Actual 1.05. System is 20 years old but running properly at this time. Service complete.
Leonardo G.

Leonardo G.

In Mesa, AZ: PREVENTATIVE MAINTENANCE- Upon arrival, cycled unit into cooling mode. Replaced intake filters and took temperature reading from supply and return. At unit, cleaned and tightened electrical connections. Took volt and amp draws from components. Checked Freon levels with super heat and subcool. Upon departure, unit is working properly and within manufacturer specifications.

Near E Glade Ave, Mesa, AZ 85206
Mesa, AZ - In Mesa, AZ:  PREVENTATIVE MAINTENANCE-  Upon arrival, cycled unit into cooling mode. Replaced intake filters and took temperature reading from supply and return. At unit, cleaned and tightened electrical connections. Took volt and amp draws from components. Checked Freon levels with super heat and subcool. Upon departure, unit is working properly and within manufacturer specifications.
Brian S.

Brian S.

In Mesa, AZ: DIAGNOSTIC- Unit is running. Checked Freon levels R22 in factory specification. Checked volt and amp draws. Compressor rated at 20.7; actual is 20.00. ODF motor rated at 2.6, actual 1.69. Indoor blower rated at 6.0, actual 4.43. Capacitor is rated 55/5/440, actual 57.2/5.1/440. Compressor is high amping and wiring for compressor is melting. Also, Freon is foaming. Mega OHM tested the compressor findings showing in orange for caution. Would recommend upgrading the system. Service complete.

Near W Obispo Ave, Mesa, AZ 85202
Mesa, AZ - In Mesa, AZ:  DIAGNOSTIC-  Unit is running. Checked Freon levels R22 in factory specification. Checked volt and amp draws. Compressor rated at 20.7; actual is 20.00. ODF motor rated at 2.6, actual 1.69. Indoor blower rated at 6.0, actual 4.43. Capacitor is rated 55/5/440, actual 57.2/5.1/440. Compressor is high amping and wiring for compressor is melting. Also, Freon is foaming. Mega OHM tested the compressor findings showing in orange for caution. Would recommend upgrading the system. Service complete.
Tom G.

Tom G.

In Mesa, AZ: PREVENTATIVE MAINTENANCE- Completed maintenance service in accordance with maintenance checklist. Replaced Schrader valve and recharged system at time of service. Need to monitor evaporative coil for wear on future services. Service complete.

Near E Jensen St, Mesa, AZ 85207
Mesa, AZ - In Mesa, AZ:  PREVENTATIVE MAINTENANCE-  Completed maintenance service in accordance with maintenance checklist. Replaced Schrader valve and recharged system at time of service. Need to monitor evaporative coil for wear on future services. Service complete.
Tom G.

Tom G.

In Mesa, AZ: DIAGNOSTIC- Small leak from from water line to float. Tightened fitting to stop leak. Inspected all coolers during repair. Systems are working properly upon departure. Service complete.

Near E Falcon Dr, Mesa, AZ 85215
Mesa, AZ - In Mesa, AZ:  DIAGNOSTIC-  Small leak from from water line to float. Tightened fitting to stop leak. Inspected all coolers during repair. Systems are working properly upon departure. Service complete.
Leonardo G.

Leonardo G.

In Mesa, AZ: Upon arrival, cycled unit into cooling mode. Took temperature readings from supply and return. At unit, cleaned and tightened electrical connections. Took volts and amp draws from components. Checked Freon levels with super heat and subcool. Upon departure, unit is working properly and within manufacturer specifications.

Near E Decatur St, Mesa, AZ 85205
Mesa, AZ - In Mesa, AZ:  Upon arrival, cycled unit into cooling mode. Took temperature readings from supply and return. At unit, cleaned and tightened electrical connections. Took volts and amp draws from components. Checked Freon levels with super heat and subcool. Upon departure, unit is working properly and within manufacturer specifications.
Tom G.

Tom G.

In Mesa, AZ: Removed old pads and installed new straw pads with distribution lines; all new floats and pumps; cleaned out all evap coolers with pressure washer and tested each cooler. Cleaned up job site.

Near E Falcon Dr, Mesa, AZ 85215
Mesa, AZ - In Mesa, AZ:  Removed old pads and installed new straw pads with distribution lines; all new floats and pumps; cleaned out all  evap coolers with pressure washer and tested each cooler. Cleaned up job site.
Tom G.

Tom G.

in Mesa, AZ: Did financing paperwork for $5000. Remainder will be paid by check on completion. Pending parts before installation. Install will start at 6am.

Near E Falcon Dr, Mesa, AZ 85215
Brian S.

Brian S.

In Mesa, AZ: QUOTE FOR 8 VIRGIN COOLERS. CUSTOMER WANTS BID WITH ELECTRICITY RAN. AND ROOF SEALED AFTER CUTTING IN DROPS. ALSO POSSIBLE PERMITS INCLUDED. NEED TO GET WITH JOSH FOR PRICING.

Near S Dobson Rd, Mesa, AZ 85202
Mesa, AZ - In Mesa, AZ:  QUOTE FOR 8 VIRGIN COOLERS. CUSTOMER WANTS BID WITH ELECTRICITY RAN. AND ROOF SEALED AFTER CUTTING IN DROPS. ALSO POSSIBLE PERMITS INCLUDED. NEED TO GET WITH JOSH FOR PRICING.
Tom G.

Tom G.

In Mesa, AZ: MOREHART AC TO SERVICE AND REPAIR SIX EVAPORATIVE COOLER SYSTEMS. PRICING INCLUDES REPLACEMENT OEM ASPEN PAD SETS, 115v 15-25k PUMPS, 3/8 FLOATS, DRAIN KITS, AND NEW DISTRIBUTION LINES, AND BLEEDERS. IN ADDITION EACH SYSTEM WILL BE PRESSURE WASHED DURING REPAIRS. MOREHART AC IS NOT RESPONSIBLE FOR ANY DAMAGE TO ROOF DURING MAINTENANCE. PENDING CUSTOMER APPROVAL. Ump 454SPB 47451 Pads 70 420 pending pricing from ump

Near E Falcon Dr, Mesa, AZ 85215
Mesa, AZ - In Mesa, AZ:  MOREHART AC TO SERVICE AND REPAIR SIX EVAPORATIVE COOLER SYSTEMS. PRICING INCLUDES REPLACEMENT OEM ASPEN PAD SETS, 115v 15-25k PUMPS, 3/8 FLOATS, DRAIN KITS, AND NEW DISTRIBUTION LINES, AND BLEEDERS. IN ADDITION EACH SYSTEM WILL BE PRESSURE WASHED DURING REPAIRS. MOREHART AC IS NOT RESPONSIBLE FOR ANY DAMAGE TO ROOF DURING MAINTENANCE. PENDING CUSTOMER APPROVAL.
Ump 454SPB
47451
Pads 70 420 pending pricing from ump
Tom G.

Tom G.

In Mesa, AZ: Completed service in accordance with maintenance checklist, please refer to to list for photos and ratings. Customer had another contractor out to warranty evaporative coil. Recommend insulating suction line to prevent water damage to insulation and potential water in return. Fan is not mounted correctly in system. Door was not secured upon arrival. Please refer to provided video. Finally liquid line is rubbing on suction line due to line being pushed back for new filter drier. Recommend having contractor out to fix repairs. Service completed.

Near N Yucca Cir, Mesa, AZ 85201
Mesa, AZ - In Mesa, AZ:  Completed service in accordance with maintenance checklist, please refer to to list for photos and ratings. Customer had another contractor out to warranty evaporative coil. Recommend insulating suction line to prevent water damage to insulation and potential water in return. Fan is not mounted correctly in system. Door was not secured upon arrival. Please refer to provided video. Finally liquid line is rubbing on suction line due to line being pushed back for new filter drier. Recommend having contractor out to fix repairs. Service completed.
Leonardo G.

Leonardo G.

In Mesa, AZ: UPON ARRIVAL FOUND RETURN PANEL UNSEALED AND ALSO BREAKING AWAY FROM UNIT. PROPERLY FASTENED SCREWS TO RETURN PANEL AND RE SEALED PANEL AS WELL AS SUPPLY PANEL. HOMEOWNER HAVING AIRFLOW ISSUES WITH ONE OF THE BEDROOMS. NOTICED IN THE ATTIC THE DUCT WORK NEEDS TO BE STRAPPED UP AND ALSO SOME RUNS NEED TO BE RE RAN TO PREVENT KINKS IN DUCT WORK TO PREVENT AIR FLOW RESTRICTIONS. HOMEOWNER WILL CONTACT COMPANY THAT INSTALLED DUCT WORK .

Near E Grandview St, Mesa, AZ 85207
Mesa, AZ - In Mesa, AZ:  UPON ARRIVAL FOUND RETURN PANEL UNSEALED AND ALSO BREAKING AWAY FROM UNIT. PROPERLY FASTENED SCREWS TO RETURN PANEL AND RE SEALED PANEL AS WELL AS SUPPLY PANEL. HOMEOWNER HAVING AIRFLOW ISSUES WITH ONE OF THE BEDROOMS. NOTICED IN THE ATTIC THE DUCT WORK NEEDS TO BE STRAPPED UP AND ALSO SOME RUNS NEED TO BE RE RAN TO PREVENT KINKS IN DUCT WORK TO PREVENT AIR FLOW RESTRICTIONS. HOMEOWNER WILL CONTACT COMPANY THAT INSTALLED DUCT WORK .
Brian S.

Brian S.

In Mesa, AZ: CYCLED SYSTEM ON IN COOLING. CHECKED VOLT AND AMP DRAWS, ALL IN FACTORY SPECIFICATION. CLEANED OUT CONTROL CABINET AND TIGHTENED ELECTRICAL CONNECTIONS. CHECKED FREON LEVELS AND PRESSURES, ALL IN FACTORY SPECIFICATION. (SEE COOLING CHECKLIST FOR DETAILS). ACID WASHED OUTDOOR COIL AND RINSED. CHANGED RETURN AIR FILTER AND CHECKED SPLITS, RETURN 76 SUPPLY 56. INDOOR COIL IS VERY DIRTY RECOMMEND AN INDOOR COIL CLEANING.

Near E Myrtle St, Mesa, AZ 85208
Tom G.

Tom G.

In Mesa, AZ: Completed service in accordance with maintenance checklist. Please refer to list for photos and ratings. System working properly upon departure.

Near E Neville Ave, Mesa, AZ 85209
Tom G.

Tom G.

In Mesa, AZ: Completed service in accordance with maintenance checklist. Please refer to list for photos and ratings. System working properly upon departure. Recommended replacing cooler due to age and condition. Customer said now is not a good time she will let us know.

Near E Main St, Mesa, AZ 85205
Brian S.

Brian S.

In Mesa, AZ: CYCLED SYSTEM ON IN COOLING. CHECKED VOLT AND AMP DRAWS, ALL IN FACTORY SPECIFICATION. CLEANED AND TIGHTENED ELECTRICAL CONNECTIONS. CHECKED FREON LEVELS AND PRESSURES, ALSO IN FACTORY SPECIFICATION. (SEE COOLING CHECKLIST FOR DETAILS). ACID WASHED OUTDOOR COIL AND RINSED. WASHED AND DRIED AIRCARE FILTER AND REINSTALLED. CHECKED SPLITS, RETURN 75 SUPPLY 55. SYSTEM IS RUNNING PROPER AT THIS TIME.

Near E Kilarea Ave, Mesa, AZ 85209
Brian S.

Brian S.

In Mesa, AZ: CHECKED ATTIC AIR HANDLER ALL LEVEL AND PROPER. CHECKED SUPPLY AND RETURN DUCT WORK IS SEALED AND LOOKS GOOD. PVC DRAIN LINE INSTALLED AND GLUED. SECONDARY DRAIN PAN IS INSTALLED WITH WET SWITCH. ATTIC IS CLEAN AND EVERYTHING LOOKS GOOD. CHECKED CONDENSER HIGH VOLTAGE IS TIGHT AND IS GOOD. INSULE TUBING IS INSTALLED PROPERLY AND NEW DISCONNECT WITH NEW WHIP LOOKS GOOD INSTALL LOOKS GOOD AND IS RUNNING PROPER. CHARGE IS LOOKING GOOD ALL COMPLETE.

Near S Greenfield Rd, Mesa, AZ 85206
Mesa, AZ - In Mesa, AZ:  CHECKED ATTIC AIR HANDLER ALL LEVEL AND PROPER. CHECKED SUPPLY AND RETURN DUCT WORK IS SEALED AND LOOKS GOOD. PVC DRAIN LINE INSTALLED AND GLUED. SECONDARY DRAIN PAN IS INSTALLED WITH WET SWITCH. ATTIC IS CLEAN AND EVERYTHING  LOOKS GOOD. CHECKED CONDENSER HIGH VOLTAGE IS TIGHT AND IS GOOD. INSULE TUBING IS INSTALLED PROPERLY AND NEW DISCONNECT WITH NEW WHIP LOOKS GOOD INSTALL LOOKS GOOD AND IS RUNNING PROPER. CHARGE IS LOOKING GOOD ALL COMPLETE.
Leonardo G.

Leonardo G.

In Mesa, AZ: UPON ARRIVAL CYCLED UNIT INTO COOLING MODE. REPLACED INTAKE FILTERS AND TOOK TEMPERATURE READINGS FROM SUPPLY AND RETURN. AT UNIT CLEANED AND TIGHTENED ELECTRICAL CONNECTIONS. TOOK VOLTS AND AMP DRAWS FROM COMPONENTS. CHECKED FREON LEVELS WITH SUPER HEAT AND SUBCOOL. HOMEOWNER STATED THERMOSTAT TEMP WOULD GO UP TO 80 DEGREES . FOUND NO ISSUE AF TIME OF SERVICE.

Near E Monte Ave, Mesa, AZ 85209
Mesa, AZ - In Mesa, AZ:  UPON ARRIVAL CYCLED UNIT INTO COOLING MODE. REPLACED INTAKE FILTERS AND TOOK TEMPERATURE READINGS FROM SUPPLY AND RETURN. AT UNIT CLEANED AND TIGHTENED ELECTRICAL CONNECTIONS. TOOK VOLTS AND AMP DRAWS FROM COMPONENTS. CHECKED FREON LEVELS WITH SUPER HEAT AND SUBCOOL. HOMEOWNER STATED THERMOSTAT TEMP WOULD GO UP TO 80 DEGREES . FOUND NO ISSUE AF TIME OF SERVICE.
Tom G.

Tom G.

In Mesa, AZ: Unit 1- bearing in motor has failed. Pump and and basket need to be replaced. Unit 2- pump and basket need to be replaced. Mineral build up for age of system is heavy. Pads need to be replaced. Unit 3- motor is failing. Pump does not work. Float is sticking. Unit 4- needs pump and basket Unit 5- needs pump and basket. New pads needed there is heavy build up. Float will not fully shut off. Unit 6- needs pump and basket. New pads needed there is heavy build up. Ducting for coolers one and two is not far enough down in shop. Listed pricing to extend them four feet down with a triangle. Scissor lift rental priced into bid. There is no drains hooked up to any of the evaporative cooler. Would recommend plumbing into original drains or connecting all to run into roof drains. Completed services for six systems at a local commercial building. Coolers are need of parts before they are functioning properly. Pending approvals.

Near E Coury Ave, Mesa, AZ 85210
Mesa, AZ - In Mesa, AZ:  Unit 1- bearing in motor has failed. Pump and and basket need to be replaced.
Unit 2- pump and basket need to be replaced. Mineral build up for age of system is heavy. Pads need to be replaced.
Unit 3- motor is failing. Pump does not  work. Float is sticking.
Unit 4- needs pump and basket
Unit 5- needs pump and basket. New pads needed there is heavy build up. Float will not fully shut off.
Unit 6- needs pump and basket. New pads needed there is heavy build up.  Ducting for coolers one and two is not far enough down in shop. Listed pricing to extend them four feet down with a triangle. Scissor lift rental priced into bid.  There is no drains hooked up to any of the evaporative cooler. Would recommend plumbing into original drains or connecting all to run into roof drains.
Completed services for six systems at a local commercial building. Coolers are need of parts before they are functioning properly. Pending approvals.
John S.

John S.

Removing a old split system out of a attic and installing a new Goodman system off of E southern ave az

Near Unnamed Road, Mesa, AZ 85206
Mesa, AZ - Removing a old split system out of a attic and installing a new Goodman system off of E southern ave az
Leonardo G.

Leonardo G.

In Mesa, AZ: UPON ARRIVAL NOTICED BATTERIES TO THERMOSTAT WERE LOW. REPLACED BATTERIES. CYCLED UNIT INTO COOLING MODE. REPLACED INTAKE FILTERS AND TOOK TEMPERATURE READINGS FROM SUPPLY AND RETURN. AT UNIT CHECKED VOLTS AND AMP DRAWS FROM COMPONENTS. CHECKED FREON LEVELS WITH SUPER HEAT AND SUBCOOL. CHECKED START AND RUN CAPACITORS. UPON DEPARTURE UNIT WORKING PROPERLY AND WITHIN SPEC.

Near N Orangewood Dr, Mesa, AZ 85203
Mesa, AZ - In Mesa, AZ:  UPON ARRIVAL NOTICED BATTERIES TO THERMOSTAT WERE LOW. REPLACED BATTERIES. CYCLED UNIT INTO COOLING MODE. REPLACED INTAKE FILTERS AND TOOK TEMPERATURE READINGS FROM SUPPLY AND RETURN. AT UNIT CHECKED VOLTS AND AMP DRAWS FROM COMPONENTS. CHECKED FREON LEVELS WITH SUPER HEAT AND SUBCOOL. CHECKED START AND RUN CAPACITORS. UPON DEPARTURE UNIT WORKING PROPERLY AND WITHIN SPEC.
Brian S.

Brian S.

In Mesa Az installing a new control board under warranty for this Amana. All working proper now.

Near E Decatur St, Mesa, AZ 85205
Mesa, AZ - In Mesa Az installing a new control board under warranty for this Amana. All working proper now.
Brian S.

Brian S.

In Mesa Az servicing a customers system. Checked volt and amp draws. Cleaned and tightened electrical connections. Checked Freon levels. Acid washed outdoor coil and rinsed and changed return filter.

Near Unnamed Road, Mesa, AZ 85206
Mesa, AZ - In Mesa Az servicing a customers system. Checked volt and amp draws. Cleaned and tightened electrical connections. Checked Freon levels. Acid washed outdoor coil and rinsed and changed return filter.
Brian S.

Brian S.

In Mesa Az servicing a customers system. Checked volt and amp draws. Cleaned and tightened electrical connections. Checked Freon levels and pressures. Acid washed outdoor coil and changed return filter.

Near E Lomita Ave, Mesa, AZ 85209
Mesa, AZ - In Mesa Az servicing a customers system. Checked volt and amp draws. Cleaned and tightened electrical connections. Checked Freon levels and pressures. Acid washed outdoor coil and changed return filter.
Brian S.

Brian S.

In Mesa Az quality inspecting a new Amana system we just installed. The job came out perfect and customer is extremely happy. Another awesome job by our install team.

Near S Quinn Cir, Mesa, AZ 85206
Mesa, AZ - In Mesa Az quality inspecting a new Amana system we just installed. The job came out perfect and customer is extremely happy. Another awesome job by our install team.
Mason  C.

Mason C.

Installed new 14 seer 3 ton hp split system

Near S Quinn Cir, Mesa, AZ 85206
Mesa, AZ - Installed new 14 seer 3 ton hp split system
John S.

John S.

Installing a new split system for a residential home right off of Broadway Rd Mesa, AZ

Near E Main St, Mesa, AZ 85205
Mesa, AZ - Installing a new split system for a residential home right off of Broadway Rd Mesa, AZ
Brian S.

Brian S.

Installing a split system in a residential home that includes new whip, thermostat, disconnect box, fuses, as well as a new drain pan and new primary and secondary drain lines in Mesa, Az

Near S Quinn Cir, Mesa, AZ 85206
Mesa, AZ - Installing a split system in a residential home that includes new whip, thermostat, disconnect box, fuses, as well as a new drain pan and new primary and secondary drain lines in Mesa, Az
Brian S.

Brian S.

In Mesa Az servicing a customers 2 systems. Checked volt and amp draws. Cleaned and tightened electrical connections. Checked Freon levels and pressures. Washed out filters and acid washed outdoor coils and rinsed.

Near E Sunland Ave, Mesa, AZ 85208
Mesa, AZ - In Mesa Az servicing a customers 2 systems. Checked volt and amp draws. Cleaned and tightened electrical connections. Checked Freon levels and pressures. Washed out filters and acid washed outdoor coils and rinsed.
Dillon G.

Dillon G.

In Mesa, Az installing a new Amana Split System.

Near E Main St, Mesa, AZ 85205
Mesa, AZ - In Mesa, Az  installing a new Amana Split System.
Tom G.

Tom G.

In Mesa performing a tune up service for an existing customer!

Near E Main St, Mesa, AZ 85213
Mesa, AZ - In Mesa performing a tune up service for an existing customer!
Leonardo G.

Leonardo G.

Performing cooling maintenance on a heat pump 14 seer ICP split system in Mesa Arizona.

Near S Quinn Cir, Mesa, AZ 85206
Mesa, AZ - Performing cooling maintenance on a heat pump 14 seer ICP split system in Mesa Arizona.
Brian S.

Brian S.

In Mesa Az servicing a customers system. Acid washed outdoor coil and rinsed. Checked volt and amp draws. Cleaned and tightened electrical connections. Checked Freon levels and washed out return filter.

Near S Ellsworth Rd, Mesa, AZ 85209
Mesa, AZ - In Mesa Az servicing a customers system. Acid washed outdoor coil and rinsed. Checked volt and amp draws. Cleaned and tightened electrical connections. Checked Freon levels and washed out return filter.
Brian S.

Brian S.

In Mesa Az servicing a customers system. Checked volt and amp draws. Checked Freon levels and pressures. Cleaned and tightened electrical connections changed the return air filters and washed the outdoor coil.

Near E Grandview St, Mesa, AZ 85207
Mesa, AZ - In Mesa Az servicing a customers system. Checked volt and amp draws. Checked Freon levels and pressures. Cleaned and tightened electrical connections changed the return air filters and washed the outdoor coil.
Brian S.

Brian S.

In Mesa servicing a customers Amana system cleaned and tightened the electrical. Changed the filters and inspected volt and amp draws.

Near N Westwood Cir, Mesa, AZ 85201
Mesa, AZ - In Mesa servicing a customers Amana system cleaned and tightened the electrical. Changed the filters and inspected volt and amp draws.
John S.

John S.

Removing a old split system and installing a new amana split system

Near E Encanto St, Mesa, AZ 85205
Mesa, AZ - Removing a old split system and installing a new amana split system
Brian S.

Brian S.

In Mesa servicing a contract customers newer Amana we installed. Cleaned out the burners. Adjusted gas flow pressure. Removed and cleaned the flame sensor and changed the return air filters. Ready for the cold weather.

Near E Lomita Ave, Mesa, AZ 85209
Mesa, AZ - In Mesa servicing a contract customers newer Amana we installed. Cleaned out the burners. Adjusted gas flow pressure. Removed and cleaned the flame sensor and changed the return air filters. Ready for the cold weather.
Leonardo G.

Leonardo G.

Performing heating maintenance on a Mortex gas furnace in a mobile home park in the city of Mesa

Near S Alma School Rd, Mesa, AZ 85210
Brian S.

Brian S.

In Mesa servicing a high efficient Amana unit we installed this year. Checked volt and amp draws, cleaned and tightened electrical connections, checked Freon levels and pressures and changed the return air filter unit is looking perfect.

Near E Kilarea Ave, Mesa, AZ 85209
Mesa, AZ - In Mesa servicing a high efficient Amana unit we installed this year. Checked volt and amp draws, cleaned and tightened electrical connections, checked Freon levels and pressures and changed the return air filter unit is looking perfect.
Leonardo G.

Leonardo G.

In Apache junction performing fall maintenance on a York package system.

Near S Meridian Rd, Mesa, AZ 85208
Mesa, AZ - In Apache junction performing fall maintenance on a York package system.
Brian S.

Brian S.

In Mesa. Servicing an Amana we installed last year. Tightened electrical connections. Checked Freon levels changed return air filter and washed the outdoor coil. The customer is ready for the cold months ahead.

Near E Russell Cir, Mesa, AZ 85207
Mesa, AZ - In Mesa. Servicing an Amana we installed last year. Tightened electrical connections. Checked Freon levels changed return air filter and washed the outdoor coil. The customer is ready for the cold months ahead.
Brian S.

Brian S.

In Mesa servicing an older unit found the run capacitor bad on this GOODMAN unit. Installed new Run Capacitor unit is working proper at this time.

Near E Fox Cir, Mesa, AZ 85205
Mesa, AZ - In Mesa servicing an older unit found the run capacitor bad on this GOODMAN unit. Installed new Run Capacitor unit is working proper at this time.
Brian S.

Brian S.

In Mesa for a customer that the system would not keep up, checked out the unit and found that the run capacitor went bad. Replace the run cap and the unit is back up and running

Near East Starkey Avenue, Mesa, AZ 85212
Tom G.

Tom G.

In Mesa performing a preventative maintenance service on a commercial building! Did a full safety inspection on the unit, as well as did and acid wash to the exterior condensing coils!

Near W Camino St, Mesa, AZ 85201
Mesa, AZ - In Mesa performing a preventative maintenance service on a commercial building! Did a full safety inspection on the unit, as well as did and acid wash to the exterior condensing coils!
Brian S.

Brian S.

In Mesa doing a QC on a new Goodman we just installed all looks good unit came out very nice! Proud of our guys another good install in the books!

Near E Merlin Pl, Mesa, AZ 85206
Mesa, AZ - In Mesa doing a QC on a new Goodman we just installed all looks good unit came out very nice! Proud of our guys another good install in the books!
Brian S.

Brian S.

In Mesa on a breakdown found a bad run capacitor on the unit installed new capacitor on 7 year old system. All is running proper completed on repair.

Near Mobile Home Park, Mesa, AZ 85208
Mesa, AZ - In Mesa on a breakdown found a bad run capacitor on the unit installed new capacitor on 7 year old system. All is running proper completed on repair.